BUNDLE MADE OF 4 HIGHLY DETAILED AIRPLANES FOR DAZ STUDIO 4.1 WITH IRAY AND GREATER.
MANY POSSIBILITIES OF CREATING DIFFERENT PAINT SCHEMES AND POSITIONS. READ CAREFULY THE ReadMe.
DIALS :
- FN-Aileron Roll Left/Right
- FN-Attitude Bank Left/Right
- FN-Attitude Climb/Descent
- FN-Attitude Climb/Descent
- FN-Elevator Pitch Up/Down
- FN-Gear Suspension Both
- FN-Gear Suspension Left
- FN-Gear Suspension Right
- FN-Open Door Lower
- FN-Open Door Upper
- FN-Rotate Main Wheels
- FN-Rotate Prop
- FN-Rotate all Wheels (proportional)
- FN-Rudder Yaw Left/Right
- FN-Ski Rotate Up/Down Both
- FN-Ski Rotate Up/Down Left
- FN-Ski Rotate Up/Down Right
- FN-Ski Rotate Up/Down Tail
- FN-Standing on Ground (Skis)
- FN-Standing on Ground (Wheels)
- FN-Throttle
- FN-Version with Floats (On/off)
- FN-Version with Skis (On/off)
- FN-Version with Wheels (On/off)
- FN-Wheel Profile Round
The functions for Elevator, Rudder and Aileron move the surfaces and the respective steering input (Stick or Pedals)
FN-Throttle moves the both throttle handles in the cockpit. Increasing the throttle over about 6% will make the static Prop invisible, while making the "Rotating Prop"-Disk visible.
FN_Standing on Ground sets the "Piper_J3_Cub_MainBody" into the right Angle for standing on Ground. Changing the heading can be done in the "Piper J-3 Cub"-Node above the MainBody without messing up the Angle of the standing plane.
"FN_Standing on Ground (Skis)" Sets the MainBody into the fitting Angle and rotates the three Skis so that they stand flat on the Ground.
The FN-Attitude... Parameters move the Plane in the selected attitude, while moving the corresponding surfaces.
For less flat and more round Tire profile use "FN-Wheel Profile Round"
For the L-4 Variant just select the J-3 and load the L-4 Canopy. Just parent the L-4 Canopy to the J-3 (select the canopy in the 3d viewport, right click and choose „Fit to…“ and there select the Piper J-3) and then the J-3 portion of the canopy disappears automatically :-)
Additionally there is a "spinner less" L-4 Propeller, which works same as the Canopy.
For those who like it more scale, there is a fuel tank nozzle Prop with fuel indicator as a smart prop and for the military versions there are Rocket launcher racks as well as smart props available.
In the material folder are the material Files for three variants of the Piper J-3 Cub (Classic Yellow, Swiss Cub and a "Stars and Stripes" Cub) and three variants of the Piper L-4 (Swiss Piper L-4 Cub HB-OFW, Military Piper L-4 Grasshopper, Military Piper L-4 Grasshopper (alternative variant with light grey belly)). Here you can find as well the appropriate material files for the canopy and the fuel nozzle.
In the Poses Folder are Poses for G3F, G3M, G8F and G8M to place them into the front or the back seat. Load the Piper, load the figure, apply the pose and parent the figure to the Piper_J3_Cub_MainBody to make sure, the figure follows the movements of the Piper.
16 PAINT SCHEMES ARE GIVEN IN A SEPARATE FOLDER AS EXEMPLES
11 TEMPLATES ARE GIVEN IN SEPARATE FOLDER IF YOU WANT TO GIVE YOUR OWN PAINT SCHEME USING A 2D SOFTWARE.
Software: DAZ Studio 4 With IRAY
